NF H96-330-2-1998 自动装卸车安全.电气要求.第2部分:内燃机驱动的卡车的一般要求
时间:2024-05-02 21:34:13 来源: 标准资料网 作者：标准资料网 阅读：9459
【英文标准名称】:Safetyofindustrialtrucks.Electricalrequirements.Part2:generalrequirementsforinternalcombustionenginepoweredtrucks.
【原文标准名称】:自动装卸车安全.电气要求.第2部分:内燃机驱动的卡车的一般要求
【标准号】:NFH96-330-2-1998
【标准状态】:作废
【国别】:法国
【发布日期】:1998-04-01
【实施或试行日期】:1998-04-05
【发布单位】:法国标准化协会(FR-AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:规范(验收);防电击;机器的保安装置;电气工程;电气设备;电气安全;定义;设计;安全;安全要求;起动电池组;内燃机;危害;紧急切断;工业用货车;生产
【英文主题词】:Definition;Definitions;Design;Electricalengineering;Electricalequipment;Electricalsafety;Emergencycut-out;Hazards;Industrialtrucks;Internalcombustionengines;Production;Protectionagainstelectricshocks;Safety;Safetyappliancesformachines;Safetyrequirements;Specification(approval);Starterbatteries
【摘要】:
【中国标准分类号】:J83
【国际标准分类号】:53_060
【页数】:12P.;A4
【正文语种】:其他
【英文标准名称】:Accuracyclasses1,6,2,5and4,0;pressuregaugesof63mmcasediameterwithdiaphragmelementparalleltoplaneofdial;dimensionsandnominalranges
【原文标准名称】:带板簧的过压测量仪.外壳直径为63mm.板簧与刻度盘平行.精度级别为1.6.2.5和4.0.尺寸和指示范围
【标准号】:DIN16027-1976
【标准状态】:作废
【国别】:
【发布日期】:
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:
【国际标准分类号】:
【页数】:
【正文语种】:
Product Code:SAE AS586
Title:Wheel and Brake (Sand and Permanent Mold) Castings Minimum Requirements for Aircraft Applications (NONCURRENT Jan 2005)
Issuing Committee:A-5a Wheels, Brakes And Skid Controls Committee
Scope:This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.